eos 1n bc出错

ltkun · 发表于 2012-2-5 12:17

马上注册咔够，结识更多爱好摄影器材朋友

您需要登录才可以下载或查看，没有帐号？注册

x

小日本代购的1n买来就是bc出错的网上查了一下因为我这个是按快门的时候出现bc所以很容易解决
大概花了十分钟不到
具体看这个链接
http://eosdoc.com/manuals/?q=BCerror

regarding the "bc" indication.
i have found many eos-1 and eos-1n's that can be fixed fairly easy if the bc code appears immediately after the shutter button is pressed (meaning that there are no actions heard or noticed in the camera's machinery)and if repressing the shutter button to first (focus/exposure) position clears the bc indication.
this is caused by sticking mirror magnet or it's linkage.
to correct this you must remove front cover and clean affected area with no residue plastic safe cleaner.
inside camera front on left upper corner of the mirror box is the mirror magnet cover (little plastic cube).press in on this cube firmly toward rear of camera while pressing the shutter at the same time,this may take many tries.the shutter should trip and work properly.this is only to free up parts.
next carefully remove front face of plastic cube with an exacto knife(dont damage the magnet windings.
spray small amount of cleaner into cover pointing toward rear of camera,immediatelly press shutter and fire off several shots.if it fails repeat what you did at first(press magnet toward rear and press shutter when the bc is not displayed.let dry and repeat until shutter works reliably.dont over do it allow cleaner to evaporate between tries

看不懂等下再解释

寒山听雪 · 发表于 2012-2-9 11:18

兄弟，太感谢您了，真不知道说什么好了，这个办法非常好用，我买的eos1n,按这种办法已经搞定，太令人高兴了。

ltkun · 发表于 2012-2-10 14:32

原帖由 寒山听雪 于 2012-2-9 11:18 发表
兄弟，太感谢您了，真不知道说什么好了，这个办法非常好用，我买的eos1n,按这种办法已经搞定，太令人高兴了。

哈总算帮到一个人了欣慰一下

wanggang · 发表于 2012-2-10 14:41

解释下，帮助更多的人。。。

寒山听雪 · 发表于 2012-2-10 15:31

1. 前盖拆5个螺丝，一个在右边皮革里要起开点胶皮，能拆下螺丝即可，然后把前盖左边撬开一些，然后装上小手柄，刚好，支撑前盖，能看到，在眼罩左下角一个透明方塑料盒，里面就是那个镜磁铁了，把塑料盒，用修表的平口螺丝刀上面沿边轻轻翘起，边按快门，边用小螺丝刀从上下顶，按磁铁，能感觉到磁铁一点点活动，就能听到反光镜就，啪啪的响了，如果不行反复，多次就行了。，然后，该不用顶磁铁，按快门就能动作了。但过一段时间一般又不行了，如果你的过一夜，还正常就不用继续了，否则，按下面办。
2. 如果能动作了，那就用牙签裹上一点棉花，粘上无水酒精，涂抹到磁铁壳上，感觉能渗到缝隙里就行，太少，就表面有，没有用，太多，恐怕不好吧。然后，多次按快门，让磁铁不断动作，也就是为了，让酒精能进道粘连空隙。等过几个小时，感觉酒精都挥发完后，再清洗，直到，放一天，两天都没问题，估计就行了吧。我的清洗了3次了，已经一天没问题了。看看能坚持几天。
3. 仅供参考，损坏您的相机，本人概不负责。

[ 本帖最后由寒山听雪于 2012-2-10 15:35 编辑 ]